This item is noncancelable and nonreturnable.
The C 10:8X is an 8-channel amplifier that delivers 8 x 125 W* at 4 ohms, 8 ohms, 16 ohms or 70 Vrms (250 W at 100 Vrms is available by bridging two channels) from a 2U chassis.This amplifier is uniquely capable of adapting to a wide variety of demanding load conditions. Each channel has an individually configurable Voltage Peak Limiter (VPL), which allows the output to be optimized for any loudspeaker load – whether a single large subwoofer or a series of small 70 V loudspeakers (100 V in bridge mode). VPL works in combination with adjustable input gain (adjustable in 4-channel blocks) to achieve maximum headroom regardless of input levels or output impedances. Additionally a 35 Hz high pass filter may be inserted in each 4-channel section. Every C Series amplifier is ready for the NomadLink® network right out of the box. With NomadLink®, key amplifier parameters are displayed via DeviceControl PC software, and remote control Maximum continuous output power, all 8 channels driven, VPL set at 100 V and Gain set at 32 dB.
- Eight channels in 2U
- High continuous output power of 125 W per channel at 70 V, 4 ohms, 8 ohms, and 16 ohms
- All channels individually selectable for lo-Z or hi-Z
- Bridged operation
- High efficiency for lower thermal stress
- General Purpose Input/Output (GPIO)
- NomadLink® network ready
- Universal Power Factor Corrected PSU with IEC inlet
- Efficient cooling
- Comprehensive circuit protection and fault indication
- Phoenix-style input connectors and barrier strip output connectors
- Amplifier Signal Type - Audio
- Amplifier Type - Power Amplifier
- Maximum Frequency Response (Bandwidth): 20 kHz
- Maximum Frequency Response (Bandwidth): 20000 Hz
- Minimum Frequency Response (Bandwidth): 20 Hz
- Minimum Frequency Response (Bandwidth): 0.02 kHz
- Impedance: 20000 ohm
- Number of Channels: 8
- Number of Watts Per Channel: 125 Watt
- Power Handling: 1000 Watt
- Signal to Noise Ratio: 112 dB
- Total Harmonic Distortion + Noise (THD+N): 0.10 %
- AC Voltage: 265 Volts
- Current Draw: 5 Amps
- Depth: 13.50 in
- Height: 3.46 in
- Width: 19.02 in
- Product Weight: 18.74 lbs
- THD at 1 kHz and 1 dB below clipping: <0.05%
- Channel separation (Crosstalk) at 1 kHz: >70 dB
- Frequency response (1 W into 8 ohms) +0/-3 dB: 6.8 Hz - 34 kHz
- Input Common Mode Rejection, CMR: 50 dB
- Output impedance @ 100 Hz: 48 mOhm
- VPL, selectable per ch. 3): 100, 63, 45, 32 V
- VPL, when bridged 3) 1): 200, 126, 90, 64 V
- Voltage Peak Limiter mode (per ch.): Hard / Soft
- Amplifier gain selectable (all channels): 29, 32, 35, 38 dB
- Default gain: 32 dB
- Level adjustment (per ch.): Front-panel potentiometer, 21 position detented from -inf to 0 dB, hidden behind security panel/dust filter grille
- Input connectors (per ch.): 3-pin Phoenix, electronically balanced
- Output connectors (per ch.): Barrier strip 2-pole screw terminals
- Output bridge mode: A+B and/or C+D, inputs A and C are input source
- NomadLink® network: On board, 2 x RJ45 connectors
- Intelligent fans (on/off): Yes, depending on presence of output signal
- Power on/off and Remote enable on/off: Individual switches on front-panel
- Cooling: Two fans, front-to-rear airflow, temperature controlled speed
- General Purpose Outputs (GPO): Contact Closure types, 2-pole Phoenix
- General Purpose Inputs (GPI): Contact Closure types, 2-pole Phoenix
Please contact us for any questions regarding this product.