DTP DVI 4K 230 Tx

by Extron
$100.00
SKU 60-1272-12

This item is noncancelable and nonreturnable. 

The Extron DTP DVI 4K 230 Tx is a transmitter for sending DVI-D video, audio, and bidirectional RS‑232 and IR signals up to 230 feet (70 meters) over a shielded CATx cable to Extron DTP®‑enabled products. It provides an economical and effective means for extending single link DVI-D or HDMI signals. In addition, the DTP DVI 4K 230 Tx accepts analog stereo audio signals for simultaneous transmission over the same shielded twisted pair cable. It supports video signals at resolutions up to 4K. The transmitter is equipped with a buffered DVI loop-through output to support a local computer monitor. The compact enclosure size and remote power capability make the DTP DVI 4K 230 Tx ideal for discreet placement in lecterns, beneath tables, or wherever needed to meet application requirements.

Specifications

DTP DVI 230 4K Tx/Rx
TRUE 4K specification
   
   Frame rate1  24, 25, 30, 50, or 60 fps
   Chroma sampling1  4:4:4, 4:2:2, or 4:2:0
   Color bit depth1  8 bits per color
   Signal type  HDMI 1.4, HDCP 2.3
   Max. video data rate  10.2 Gbps (3.4 Gbps per color)
    NOTE     1Subject to the maximum data rate limit. Use our calculator (www.extron.com/8Kdatarate) to determine video parameters supported by this data rate.
 NOTE     This product consists of a transmitter (DTP DVI 4K 230 Tx) and a receiver (DTP DVI 4K 230 Rx), sold separately, with a twisted pair cable linking the transmitter and receiver.
 NOTE     *Appropriate DVI-D to HDMI cables or adapters are required for DVI signal input/output.
Video
   Maximum data rate  10.2 Gbps (3.4 Gbps per color)
   Maximum pixel clock  300 MHz
   Resolution range  Up to 2560x1600* @ 60 Hz or
4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz,
4K/UHD @ 60 Hz with 4:2:0 chroma subsampling
(* reduced blanking)
   Color bit depth  8, 10, or 12 bits — subject to the maximum data rate limit
   Formats  RGB and YCbCr digital video
   Standards  DVI 1.0, HDMI 1.4, HDCP 2.3, CEA-861E
Video input — transmitter
   Number/signal type  1 single link DVI-D (or HDMI*) input
1 single link DVI-D (or HDMI*) local loop-through
   Connectors  2 female DVI-I
Interconnection between transmitter and receiver
   Connectors  1 female RJ-45 per unit
   Termination standard  TIA/EIA T568B
   Signal transmission distance 
      1080p @ 60 Hz  Up to 230' (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
      2560x1600 @ 60 Hz  Up to 130' (40 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
      4K/UHD @ 30Hz and 60 Hz  Up to 130' (40 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
   Cable requirements  Solid conductor, 24 AWG or better
   Cable recommendations  400 MHz bandwidth, STP (shielded twisted pair)
    NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
Video output — receiver
   Number/signal type  1 single link DVI-D (or HDMI*)
   Connectors  1 female DVI-I
Audio
   Gain  Unbalanced output: 0 dB; balanced output +6 dB
   Frequency response  20 Hz to 20 kHz, ±0.5 dB
   THD + Noise  0.03% @ 20 Hz to 20 kHz at maximum output
   S/N  >90 dB, at maximum output (15 dBu), balanced (unweighted)
   Stereo channel separation  >80 dB @ 1 kHz to 20 kHz
Audio input
   Number/signal type  1 PC level stereo, unbalanced
    NOTE     Analog audio is not embedded onto the digital video signal.  Embedded digital audio is not de-embedded from the digital video signal.
   Connectors  (1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground)
   Impedance  >10k ohms, DC coupled
   Nominal level  -10 dBV (316 mVrms)
   Maximum level  +7 dBV (unbalanced)
    NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output
   Number/signal type  1 stereo (2 channel), balanced/unbalanced
   Connectors  (1) 3.5 mm captive screw connector, 5 pole
   Impedance  50 ohms unbalanced, 100 ohms balanced
   Gain error  ±0.1 dB channel to channel
   Maximum level (600 ohm)  >+11 dBu, balanced
Communications — external device (pass-through, unidirectional or bidirectional)
   Serial control port input/output 
      Transmitter  RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (±5 V) (connector is shared with IR control port)
      Receiver  1 set of proprietary signals on a female RJ-45 jack
   Serial control port output/input 
      Transmitter  1 set of proprietary signals on a female RJ-45 jack
      Receiver  RS-232 via a 3.5 mm, 3 pole captive screw connector
   Baud rate and protocol  300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity
   Serial control pin configuration  1 = Tx, 2 = Rx, 3 = GND
   IR control port  (1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
   IR control pin configuration  3 = GND, 4 = IR Tx, 5 = IR Rx
General
   Power supply  External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts
   Power consumption 
      Transmitter 
         Device  3.4 watts
         Device and power supply  4.8 watts
         Remote power budget  12 watts
      Receiver 
         Device  4.2 watts
         Device and power supply  5.8 watts
         Remote power budget  12 watts
    NOTE     Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.
   Temperature/humidity  Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
   Cooling  Convection, no vents
   Thermal dissipation 
      Transmitter 
         Device  10.3 BTU/hr
         Device and power supply  15.1 BTU/hr
      Receiver 
         Device  13.0 BTU/hr
         Device and power supply  18.6 BTU/hr
   Mounting
      Rack mount  Yes, with optional 1U high rack shelf
      Furniture mount  Yes, with optional under-desk mounting kit
   Enclosure type  Metal
   Enclosure dimensions 
      Transmitter  1.0" H x 4.3" W x 3.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors.)
      Receiver  1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.)
   Product weight 
      Transmitter  0.5 lbs (0.3 kg)
      Receiver  1.0 lb (0.5 kg)
   Regulatory compliance  CE, c-UL UL, CE**, C-tick, FCC Class A**, ICES, VCCI,
UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply.
Complies with the appropriate requirements of RoHS, WEEE
    NOTE     **CE and FCC testing is conducted with STP (shielded twisted pair) I/O cable.
   Product warranty  3 years parts and labor
   Everlast power supply warranty  7 years parts and labor
    NOTE     All nominal levels are at ±10%.
    NOTE     Specifications are subject to change without notice.
(5342-D15)
Shipping Dimensions and Weights
    Part # Height Width Depth

 

    60-1272-12 2.94" (7.5 cm) 7.5" (19.1 cm) 10.5" (26.7 cm)

 

Please contact us for any questions regarding this product.


People who bought this product, also bought