NetPA 1001-70V AT, Dante Amp.
NetPA 1001-70V AT, Dante Amp.

NetPA 1001-70V AT, Dante Amp.

by Extron
Sale
$395.00
$197.50
SKU 60-1501-01

This item is noncancelable and nonreturnable. 

The Extron NetPA 1001‑70V AT is a half rack 1U, convection cooled power amplifier featuring Dante™. It delivers a single channel of 100 watts at 70 volts for high impedance speaker systems. The NetPA® amplifier receives a channel of audio from a Dante-enabled device, allowing for decentralized distribution of audio throughout a building. In addition to amplifying incoming Dante audio, the NetPA amplifier features a line level output that can simultaneously feed an additional speaker zone or audio system. It is an ENERGY STAR® qualified amplifier with an Extron exclusive, highly efficient, advanced Class D amplifier design. It also features patented CDRS™ – Class D Ripple Suppression that provides improved signal fidelity over conventional Class D amplifiers.


Audio
   Crosstalk  >75 dB @ 1 kHz
Audio input
   Number/signal type 
      NetPA 502 AT  1 stereo or 2 mono
      NetPA 1001-70V AT  1 mono
   Connectors  1 RJ-45
   Maximum level  0 dBFS (digital)
Audio processing
   D/A conversion  24 bit, selectable sampling rate
AT ports — audio transport
   Transmission  Dante/AES-67, software selectable
   Connector  1 RJ-45 connector, 1-port 100 Mbps to Dante interface
   Inputs 
      NetPA 502 AT  2 channels Rx
      NetPA 1001-70V AT  1 channel Rx
   Audio format  24-bit uncompressed, selectable at 44.1, 48, 88.2, and 96 kHz sampling rate
   Latency  Deterministic, based on user selection: 2.0 ms (default), 5.0 ms
Audio line output
   Number/signal type 
      NetPA 502 AT  2 channels, balanced/unbalanced
      NetPA 1001-70V AT  1 channel, balanced/unbalanced
   Connectors 
      NetPA 502 AT  (1) 3.5 mm captive screw connector, 6 pole
      NetPA 1001-70V AT  (1) 3.5 mm captive screw connector, 3 pole
   Impedance  50 ohms unbalanced, 100 ohms balanced
   Maximum level (at 0 dBFS digital input)  >+15 dBu balanced; +9 dBu unbalanced
   Frequency response  20 Hz to 20 kHz, ±1 dB
   THD + Noise  0.03% @ 1 kHz at nominal level,
0.3% @ 20 kHz at nominal level
   S/N  >90 dB, at maximum output (unweighted)
    NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio speaker output
   Number/signal type 
      NetPA 502 AT  2 channels, 4 or 8 ohms
      NetPA 1001-70V AT  1 channel, 70 V
   Connectors 
      NetPA 502 AT  (1) 5.08 mm screw lock captive screw connector, 4 pole
      NetPA 1001-70V AT  (1) 5.08 mm screw lock captive screw connector, 2 pole
    NOTE     These connectors accept wires of 22 AWG to 12 AWG.
   Load impedance 
      NetPA 502 AT  4 ohms minimum
      NetPA 1001-70V AT  50 ohms minimum
   Amplifier type  Class D
   Output power 
      NetPA 502 AT  50 watts rms per channel, 4 ohms, 1 kHz, 0.1% THD
25 watts rms per channel, 8 ohms, 1 kHz, 0.1% THD
      NetPA 1001-70V AT  100 watts rms, 70 V, 1 kHz, 0.1% THD
   Frequency response 
      NetPA 502 AT  20 Hz to 20 kHz, +1/-3 dB @ 1 watt
      NetPA 1001-70V AT  20 Hz to 20 kHz, +1/-3 dB @ 1 watt
   THD + Noise  <0.1% @ 1 kHz, 3 dB below clipping
   S/N  >90 dB, 20 Hz - 20 kHz, unweighted
   High pass filter 
      NetPA 1001-70V AT  80 Hz, 12 dB per octave rolloff for 70 V line output (switch selectable)
Communications — amplifier
   Control port  (1) 3.5 mm captive screw connector, 2 pole
   Pin configurations 
      Standby power control (contact closure) 

Pin 1 = standby, pin 2 = Gnd
General
   Power supply  Internal
Input: 100-240 VAC, 50-60 Hz, 0.5 A
   Power consumption and thermal dissipation 
      NetPA 502 AT
  115 VAC, 60Hz 230 VAC, 50Hz
AC Line
Current		 AC Power
Consumed		 Thermal
Dissipation		 AC Line
Current		 AC Power
Consumed		 Thermal
Dissipation/
Condition A W W BTU/hr A W W BTU/hr
Active (1/8 power), all
channels driven		 8Ω 0.3 14.6 8.3 28 0.2 17 10.7 36
4Ω 0.4 22.3 9.8 33 0.3 24 11.7 40
Quiescent (idle) 0.1 7.4 7.4 25 0.1 9.9 9.9 34
Standby <0.1 <2 <2 <6 <0.1 <2 <2 <6

 
      NetPA 1001-70V AT
  115 VAC, 60Hz 230 VAC, 50Hz
AC Line
Current		 AC Power
Consumed		 Thermal
Dissipation		 AC Line
Current		 AC Power
Consumed		 Thermal
Dissipation
Condition A W W BTU/hr A W W BTU/hr
Active (1/8 power), all
channels driven		 70 V 0.4 22.7 10.2 35 0.3 24.1 11.6 39
Quiescent (idle) 0.1 7.6 7.6 26 0.1 9.2 9.2 31
Standby <0.1 <2 <2 <6 <0.1 <2 <2 <6

 
   Temperature/humidity  Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +104 °F (0 to +40 °C) / 10% to 90%, noncondensing
   Cooling  Convection, no vents, with internal heat sink
   Protection  Clip limiting, thermal, short circuit, DC output
   Indication  Limiter/Protect LED indicates the onset of clip limiting, thermal cycling, or short circuit
   Mounting 
      Rack mount  Yes, with optional 1U rack shelf
      Furniture mount  Yes, with optional under-desk mounting kit
   Enclosure type  Metal
   Enclosure dimensions  1.7" H x 8.7" W x 9.5" D (1U high, half rack wide)
(4.3 cm H x 22.1 cm W x 24.1 cm D)
   Product weight 
      NetPA 502 AT  2.6 lbs (1.2 kg)
      NetPA 1001-70V AT  2.6 lbs (1.2 kg)
   Regulatory compliance  BSEN 60065, CE, C-tick, c-UL, EN 55103-1, EN 55103-2, ENERGY STAR®, 
FCC Class B, ICES, IEC 60065, RoHS, UL, UL 60065, VCCI Class B, WEEE.
   Product warranty  3 years parts and labor
   Everlast power supply warranty  7 years parts and labor
    NOTE     All nominal levels are at ±10%.
    NOTE     Specifications are subject to change without notice.
(4536-D8)
Shipping Dimensions and Weights
    Part # Height Width Depth Weight
    60-1501-01 4.5" (11.4 cm) 13.75" (34.9 cm) 14.0" (35.6 cm) 5.0 lbs (2.27 kg)

 

Please contact us for any questions regarding this product.

 


People who bought this product, also bought